[Possible Breakage] t1308 - Bad return value from test-tool

> t1308 has me perplexed - this is an old breakage on the NonStop platform,
> that I have just gotten around to checking with the new bash version we
> have. When running sub-test 23, the following was reported:
> 
> Value not found for "foo.bar"
> test_expect_code: command exited with 1, we wanted 2 test-tool config
> configset_get_value foo.bar a-directory
> 
> However, when I looked inside t/helper/test-config.c, every path reporting
> "Value not found" has a goto exit1 not exit2. It seems, from the code, that
> the test is actually incorrect and should be expecting 1 not 2, and that it
> is working properly on NonStop (but the test fails as a result).

> On Fri, Feb 08, 2019 at 04:42:19PM -0500, Randall S. Becker wrote:
> 
> > t1308 has me perplexed - this is an old breakage on the NonStop
> > platform, that I have just gotten around to checking with the new bash
> > version we have. When running sub-test 23, the following was reported:
> >
> > Value not found for "foo.bar"
> > test_expect_code: command exited with 1, we wanted 2 test-tool config
> > configset_get_value foo.bar a-directory
> >
> > However, when I looked inside t/helper/test-config.c, every path
> > reporting "Value not found" has a goto exit1 not exit2. It seems, from
> > the code, that the test is actually incorrect and should be expecting
> > 1 not 2, and that it is working properly on NonStop (but the test fails as a
> result).
> 
> We're expecting it to report an error reading the directory, not "value not
> found". Which would yield code 2.
> 
> It sounds like you might need to set FREAD_READS_DIRECTORIES in your
> config.mak.

> still results in 
> 
> Value not found for "foo.bar"
> test_expect_code: command exited with 1, we wanted 2 test-tool config configset_get_value foo.bar a-directory
> not ok 23 - proper error on directory "files"
> #
> #               echo "Error (-1) reading configuration file a-directory." >expect &&
> #               mkdir a-directory &&
> #               test_expect_code 2 test-tool config configset_get_value foo.bar a-directory 2>output &&
> #               grep "^warning:" output &&
> #               grep "^Error" output >actual &&
> #               test_cmp expect actual
> #
> 
> I don't think that helped. While fopen can open a directory, fread
> does not return any data in this platform. readdir or nftw/ftw are
> pretty much the only options. However, the code still goes down the
> goto exit1 path in this situation.

> On Sat, Feb 09, 2019 at 01:08:01PM -0500, Randall S. Becker wrote:
> 
> > > It sounds like you might need to set FREAD_READS_DIRECTORIES in your
> > > config.mak.
> >
> > Setting FREAD_READS_DIRECTORIES = UnfortunatelyYes
> 
> Silly question, but you did rebuild after setting that, not just re-run the tests,
> right?

> > still results in
> >
> > Value not found for "foo.bar"
> > test_expect_code: command exited with 1, we wanted 2 test-tool config
> > configset_get_value foo.bar a-directory not ok 23 - proper error on
> directory "files"
> > #
> > #               echo "Error (-1) reading configuration file a-directory." >expect
> &&
> > #               mkdir a-directory &&
> > #               test_expect_code 2 test-tool config configset_get_value foo.bar
> a-directory 2>output &&
> > #               grep "^warning:" output &&
> > #               grep "^Error" output >actual &&
> > #               test_cmp expect actual
> > #
> >
> > I don't think that helped. While fopen can open a directory, fread
> > does not return any data in this platform. readdir or nftw/ftw are
> > pretty much the only options. However, the code still goes down the
> > goto exit1 path in this situation.
> 
> Hrm. That's the exact case FREAD_READS_DIRECTORIES is supposed to help.
> It does an fstat() after fopen()ing the file to see if it points to a directory, and
> if so closes it immediately and returns EISDIR.
> 
> Can you confirm via debugger (or printf statements) that we make it into
> git_fopen, and what the resulting st.st_mode we see looks like?